InspectAPedia tolerates no conflicts of interest. We have no relationship with advertisers, products, or services discussed at this website.Peel and stick flashing tape or membrane:This article describes the selection and installation of peel-and-stick flashing membranes used on building exteriors to seal housewrap joints and to seal against air or water leaks around windows, doors, or other openings.Our photo at page top shows Typar® flashing tape installed above a new window. A better practice laps the housewrap over rather than under the stick-on flashing tape, a better detail but one omitted by many builders.We also provide a to this topic, or you can try the page top or bottom as a quick way to find information you need. Using Building Flashing Membranes - Peel & Stick Flashing TapeHow to buy & use flashing tape or peel and stick housewrap tape to prevent water leakage through building exteriors, cause, cure, prevention. Using flashing tapes & membranes on buildings.What is the best way to flash around windows & doors and how should flashing tape be used at these openings?This article shows best practices, common practices, and some not-so-good practices using peel-and stick flashing tape around windows, doors, and other building wall penetrations.
John Wiley & Sons, 2006. ISBN-10:, ISBN-13: 9369, Hardcover: 320 pages, available from and also. See our of this publication., Lagrangeville, NY. Galow can be reached by email: or by telephone: 914-474-6613. Galow specializes in residential construction including both new homes and repairs, renovations, and additions.
technical consultant on networking, LAN design, applications support., 914-204-1749, email:., Advantage Home Inspections, Flemington N.J. 08822 home inspector, 908-806- 6364, Home, Radon & Termite Inspections, Central & Parts of North New Jersey, email:Books & Articles on Building & Environmental Inspection, Testing, Diagnosis, & Repair. Our recommended books about building & mechanical systems design, inspection, problem diagnosis, and repair, and about indoor environment and IAQ testing, diagnosis, and cleanup are at the.
How To Install Blueskin Window Flashing
Also see our., Steve Bliss (Editor), The Journal of Light Construction, Williston VT, 2010 ISBN 10: 1-928580-42-4, ISBN 13: 978-1-928580-42-3, available from. has generously given reprint permission to InspectAPedia.com for this article. All rights and contents are ©Journal of Light Construction and may not be reproduced in any form.120 Carlton Street Suite 407, Toronto ON M5A 4K2. Tel: (416) 964-9415 1-800-268-7070 Email:. The firm provides professional & &. Alan Carson is a past president of ASHI, the American Society of Home Inspectors.
Thanks to Alan Carson and Bob Dunlop, for permission for InspectAPedia to use text excerpts from The Home Reference Book & illustrations from The Illustrated Home.
In this video, This Old House general contractor Tom Silva explains how to install a window.Steps:1. Staple 15-pound builder's felt along bottom of window opening.2.
Apply adhesive-backed waterproof membrane over the felt; cut the corners and fold the excess membrane over the rough sill.3. Cut small pieces of waterproof membrane and cover voids in corners of opening.4. Apply a wide strip of waterproof membrane to each side of the opening; run the flashing past the header and overlap the bottom flashing.5.
Set the window in the opening.6. From inside, slip shims under the window.7.
Center window in the opening, then check the bottom of the window for level.8. Drive a single nail through the nailing flange on the window's high side.9. Raise the low side of the window to level, then nail through the flange.10. Check vertical edge of the window for plumb; shim if necessary.11. Measure the opposing diagonals of the window to ensure that it's square.12.
Finish nailing the window to the wall.13. Apply a wide strip of waterproof membrane across the top of the window.